This is PermitBase’s published record for Steamboat Springs as of 2026-08-14. It has since been superseded — see the current record. A historical record reflects what PermitBase had verified at that time; it may not capture a real-world change the jurisdiction had made but PermitBase had not yet verified, and it includes any errors we later corrected. Snapshots are never edited retroactively.
Steamboat Springs building permits
VerifiedSteamboat Springs, Colorado — as published 2026-08-14.
Verified 2026-07-06 · Source
Codes adopted
Permit types & fees
Residential Building Permit (New Construction)
VerifiedRequired for new construction of single-family homes, duplexes, and townhomes within Steamboat Springs city limits. Administered entirely by the Routt County Regional Building Department under the City's own adopted 2021 IRC/IBC (RCRBD-enforced), including the City's Table R301.2(1) climatic/geographic design criteria (115 mph wind speed, Seismic Design Category C, 48-inch frost depth, site-specific Case-Study-Area ground snow load) and the amended IWUIC Class A roofing requirement.
Verified 2026-07-06 · Source
Requirements
- Must comply with the City's Table R301.2(1) Climatic and Geographic Design Criteria: 115 mph ultimate design wind speed (no topographic effects), Seismic Design Category C, 48-inch minimum frost line depth, Ice Barrier Underlayment required per IRC R905.1.2, Climate Zone 7
- Ground Snow Load is NOT a fixed code value — applicant must look up the site-specific value using RCRBD's Ground Snow Load Map (Case Study Area) and apply it to the governing formula to calculate the actual roof design snow load; uncovered decks must also be designed to carry roof snow load
- Soils Report required for all new construction, submitted as a separate document, prepared and stamped by a Soils/Geotechnical Engineer or Structural Engineer
- Site Plan required for all new construction showing property lines, setbacks, and building footprint
- Structural Plans referencing the Soils Report and local Ground Snow Load values, covering footings, piers, foundations, floor/wall framing, roof plans
- Architectural Plans including Code Analysis, Floor Plan, Egress Plan, Section Views, Elevation Views, and Energy Code Compliance details
- An Architect or Engineer is required if the soils report shows swell potential with dead load requirements exceeding 500 lbs/sq ft, or if basement/retaining walls exceed 4 feet in height retaining more than 4 feet of soil
- Engineered electrical plans required if residential electrical service is 400 AMP or larger (not required below that threshold for single-family/duplex)
- Class A roof covering required under the amended IWUIC Section 504.2
- Heat Load Calculations required (may be a Deferred Submittal item)
- Blower Door Test Results or Building Commissioning Report required prior to Certificate of Occupancy (Deferred Submittal)
- All applications and plans submitted electronically only, through the CityView Portal — no paper submittals accepted
- City of Steamboat Springs Planning Department review for zoning compliance runs in parallel with RCRBD's building review
Required documents
- RequiredBuilding Permit Application (CityView Portal)Electronic submittal only, via cityview.steamboatsprings.net/portal
- RequiredSoils/Geotechnical ReportStamped by a Soils Geotechnical Engineer or Structural Engineer, submitted as its own document
- RequiredSite Plan
- RequiredStructural PlansReferencing the Soils Report and site-specific Ground Snow Load values
- RequiredArchitectural PlansCode analysis, floor plan, egress plan, sections, elevations, energy code compliance details
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Building Permit Fee — valuation $1.00 to $500.00 | $21.15 | RCRBD Permit Fee Schedule-Policies, City of Steamboat Springs section — same valuation table used county-wide |
| Building Permit Fee — valuation $500.01 to $2,000.00 | $21.15 for the first $500 plus $2.75 for each additional $100 or fraction thereof, up to and including $2,000.00 | — |
| Building Permit Fee — valuation $2,000.01 to $25,000.00 | $62.33 for the first $2,000 plus $12.60 for each additional $1,000 or fraction thereof, to and including $25,000.00 | — |
| Building Permit Fee — valuation $25,000.01 to $50,000.00 | $352.13 for the first $25,000 plus $9.09 for each additional $1,000 or fraction thereof, to and including $50,000.00 | — |
| Building Permit Fee — valuation $50,000.01 to $100,000.00 | $579.38 for the first $50,000 plus $6.30 for each additional $1,000 or fraction thereof, to and including $100,000.00 | — |
| Building Permit Fee — valuation $100,000.01 to $500,000.00 | $894.38 for the first $100,000 plus $5.04 for each additional $1,000 or fraction thereof, to and including $500,000.00 | — |
| Building Permit Fee — valuation $500,000.01 to $1,000,000.00 | $2,910.38 for the first $500,000 plus $4.28 for each additional $1,000 or fraction thereof, to and including $1,000,000.00 | — |
| Building Permit Fee — valuation $1,000,000.01 and up | $5,047.88 for the first $1,000,000 plus $3.29 for each additional $1,000 or fraction thereof | — |
| Plan Review Fee | 65% of the Building Permit Fee | Paid at application submittal, before plan review begins |
| Mandatory Routt County Use Tax Fee | (Total Valuation x 0.5) x 1% | Applies in all RCRBD jurisdictions including Steamboat Springs |
| City of Steamboat Springs Use Tax | (Total Project Valuation x 0.5) x 4.5% | Applies only inside City limits, in addition to the countywide Use Tax Fee |
| City of Steamboat Springs Excise Tax | Total Project Valuation x 1.2% | Applies only inside City limits |
Residential Addition / Interior Remodel Permit
VerifiedRequired for additions and interior alterations to existing single-family, duplex, and townhome structures in Steamboat Springs. Administered by RCRBD under the amended IRC. Review timeline and document scope both differ meaningfully by whether the project changes the building footprint.
Verified 2026-07-06 · Source
Requirements
- Additions (footprint or height change) require a Site Plan, Structural Plans, and Architectural Plans similar to new construction
- Interior renovations/alterations that do NOT change the building footprint (including exterior decks without roofs) fall under a lighter 5-business-day initial review track, though significant gut/remodels, occupancy changes, significant structural alterations, or significant fire alarm/sprinkler changes can extend that timeline
- A Licensed Structural Engineer's design may be required if walls being modified are structural, or if the project is complex enough that RCRBD requests it during review
- Engineered electrical plans required only if the project increases residential electrical service to 400 AMP or larger
- Work exempt from a permit: removal of substrate exposing floor/ceiling/wall/attic cavities for minor repair/alteration is exempt if less than 96 sq ft total is exposed (other trade permits still required if THEIR thresholds are triggered); replacement of deck boards using same-or-greater thickness material is exempt
- All submittals electronic only via the CityView Portal
Required documents
- RequiredBuilding Permit Application (CityView Portal)
- OptionalSite PlanRequired if the addition changes the building footprint or height
- RequiredStructural PlansRequired for additions and any structural alterations
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Building Permit Fee (same valuation-based schedule as new construction) | $21.15 minimum, scaling per the valuation tiers in the RCRBD Permit Fee Schedule-Policies | Identical fee table applies to unincorporated county and City of Steamboat Springs |
| Plan Review Fee | 65% of the Building Permit Fee | — |
| Mandatory Routt County Use Tax Fee | (Total Valuation x 0.5) x 1% | — |
| City of Steamboat Springs Use Tax | (Total Project Valuation x 0.5) x 4.5% | — |
| City of Steamboat Springs Excise Tax | Total Project Valuation x 1.2% | — |
Electrical Permit
VerifiedRequired for electrical work not performed under a Building Permit in Steamboat Springs. Governed by the National Electrical Code as adopted by the State of Colorado Electrical Board. RCRBD charges a flat alteration-work fee rather than a valuation-based table for standalone electrical permits.
Verified 2026-07-06 · Source
Requirements
- Electrical work performed as PART OF an issued Building Permit is exempt from these standalone fees, provided the Building Permit application included electrical labor/material cost in its valuation
- Engineered electrical plans (one-line service diagram, load calculation, grounding detail, panel schedules, equipment specs) required for new commercial construction, commercial additions/alterations, tenant finishes, and multi-family residential; NOT required for single-family/duplex UNLESS electrical service is 400 AMP or larger
- Tenant finishes using existing electrical conditions may skip the engineered plan if documented at application, but RCRBD may still require a full submittal or as-built drawings before final inspection
- All applications submitted electronically via the CityView Portal
Required documents
- RequiredElectrical Permit Application (CityView Portal)
- OptionalEngineered Electrical PlansRequired for commercial/multi-family projects, or residential service of 400 AMP or larger
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Residential Building Electrical Alteration Work (not associated with a Building Permit) | $100.00 | RCRBD Permit Fee Schedule-Policies — flat fee, not valuation-based |
| Commercial Building Electrical Alteration Work (not associated with a Building Permit) | $125.00 | — |
Plumbing Permit
VerifiedRequired for plumbing work not performed under a Building Permit in Steamboat Springs. Governed by the 2021 International Plumbing Code (IPC) as adopted. RCRBD charges a flat alteration-work fee for standalone plumbing permits rather than a valuation-based table.
Verified 2026-07-06 · Source
Requirements
- Plumbing work performed as PART OF an issued Building Permit is exempt from these standalone fees, provided the Building Permit application included plumbing labor/material cost in its valuation
- Plumbing/Fuel Gas Plans required for new commercial construction and commercial additions/alterations; RCRBD may request plumbing plans on other projects if determined necessary during review
- Routt County follows State of Colorado (DORA) regulations for when a Licensed Plumbing Engineer must prepare commercial plumbing plans
Required documents
- RequiredPlumbing Permit Application (CityView Portal)
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Residential Building Plumbing Alteration Work (not associated with a Building Permit) | $100.00 | RCRBD Permit Fee Schedule-Policies — flat fee |
| Commercial Building Plumbing Alteration Work (not associated with a Building Permit) | $125.00 | — |
Mechanical / HVAC Permit
VerifiedRequired for heating, cooling, ventilation, and fuel-gas equipment work not performed under a Building Permit in Steamboat Springs. Governed by the 2021 International Mechanical Code (IMC) and International Fuel Gas Code (IFGC) as adopted. Gas Piping/Tank work is billed under its own separate fee line from general Mechanical work.
Verified 2026-07-06 · Source
Requirements
- Mechanical work performed as PART OF an issued Building Permit is exempt from these standalone fees, provided the Building Permit application included mechanical labor/material cost in its valuation
- Mechanical Plans required for all new commercial construction, additions, or alterations to existing commercial buildings; RCRBD may request them on other projects if determined necessary
- Heat Load Calculations required for all new residential and commercial buildings or additions (may be a Deferred Submittal item required prior to sub-permit issuance)
- Gas Piping/Tank work (separate from general Mechanical/HVAC equipment) is billed under its own fee line
Required documents
- RequiredMechanical Permit Application (CityView Portal)
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Residential Mechanical Alteration Work (not associated with a Building Permit) | $100.00 | RCRBD Permit Fee Schedule-Policies — flat fee |
| Commercial Mechanical Alteration Work (not associated with a Building Permit) | $125.00 | — |
| Residential Gas Piping/Tank Alteration Work (not associated with a Building Permit) | $100.00 | — |
| Commercial Gas Piping/Tank Alteration Work (not associated with a Building Permit) | $125.00 | — |
Roofing Permit (Re-Roof)
VerifiedRequired for re-roofing work in Steamboat Springs. Governed by the amended IWUIC Class A roofing requirement (city-wide, with a narrow historic-preservation exception) plus the Table R301.2(1) ice-barrier-underlayment requirement. Falls under RCRBD's fastest initial-review track alongside siding, window, and door replacement.
Verified 2026-07-06 · Source
Requirements
- Class A roofing material required city-wide on all re-roofs (Section 504.2 of the amended IWUIC), with an exception only for Historic Registered Properties where HPC review determines Class A materials cannot be used
- Ice Barrier/Ice Shield Underlayment required per IRC Section R905.1.2, per the City's Table R301.2(1) design criteria
- Roof valley flashing, where provided, must be minimum 0.019-inch (No. 26 galvanized) corrosion-resistant metal over a 36-inch-wide, 72-lb mineral-surfaced ASTM D3909 cap sheet running the full valley length (Section 504.2.1)
- Eaves and soffits must be protected on the exposed underside by 3/4-inch solid wood or thicker, ignition-resistant material, noncombustible material, FRWT product, or 3/4-inch plywood treated with an intumescent product providing a 30-minute rating (Section 504.3)
- Gutters and downspouts must be noncombustible material (Section 504.4)
- Re-Roofing work performed as PART OF an issued Building Permit is exempt from the standalone re-roof fee below, if labor/material cost was included in that Building Permit's valuation
Required documents
- RequiredBuilding Permit Application — Re-Roof scope (CityView Portal)
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Residential Re-Roofing Permit Fee | $300.00 maximum | RCRBD Permit Fee Schedule-Policies |
| Commercial Re-Roof Permit Fee | $500.00 maximum | — |
| Mandatory Plan Review Fee (Re-Roofing and Window/Door Replacement) | $25.00 | — |
Solar Permit (Photovoltaic / Solar Thermal)
VerifiedRequired for solar photovoltaic and solar thermal installations in Steamboat Springs. A single Solar Permit covers both structural and electrical work — no separate electrical permit is needed. Fees comply with the Colorado Fair Permit Act (HB1199) cap.
Verified 2026-07-06 · Source
Requirements
- Site Plan required for ground-mount solar, showing property lines, setbacks, easements, and distances to property lines
- Roof Plan View required for roof-mount systems, showing panel locations and required fire-access walkways per building code
- Structural Plans required for both rooftop and ground-mount systems
- System size (kW), array component specs (manufacturer cut sheets), inverter specs, and electrical one-line diagram/wiring specification all required at submittal
- The Solar Permit covers ALL structural and electrical work under one permit — list all contractors performing structural or electrical work on the contacts list; no need to apply for a separate electrical permit
- Planning Department review required in parallel (may include Historic Preservation Review depending on the property) before the Solar Permit is submitted to the Building Department
- HOA review/approval strongly encouraged in advance if the property is HOA-governed (not enforced by RCRBD, but flagged in RCRBD's own checklist)
- Applicants must work directly and independently with Yampa Valley Electric Association (YVEA) for solar interconnection review/approval — YVEA does not provide plan review through RCRBD
- Where structural modification to the supporting building is required, RCRBD issues that modification work as a SEPARATE building permit billed under the standard valuation-based fee table, distinct from the solar equipment permit
Required documents
- RequiredSolar Permit Application (CityView Portal)
- RequiredSite Plan or Roof Plan ViewSite Plan for ground-mount; Roof Plan View for roof-mount systems
- RequiredStructural Plans
- RequiredElectrical one-line diagram and wiring specification
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Residential Solar Permit Fee | Capped at $500.00 total | Colorado HB1199 'Fair Permit Act' (2011) cap; local use/excise taxes not included in this cap |
| Commercial/Non-Residential Solar Permit Fee | Capped at $1,000.00 total | HB1199 cap |
| Structural modification permit (if required, separate from solar equipment permit) | Standard valuation-based Building Permit Fee table applies | Only if the roof/structure needs modification to support the array |
De-Construction / Demolition Permit
VerifiedRequired for demolition or de-construction of buildings, signs, fences, retaining walls, and other structures in Steamboat Springs. Administered by RCRBD under its De-Construction Permit Application and Policy. Within specific downtown commercial zone districts, a Final Development Plan must be approved by the City Planning Department before a Demolition Permit can be issued.
Verified 2026-07-06 · Source
Requirements
- Complete work description in the CityView application and on a Site Plan showing all structures proposed for removal
- Construction Site Management Plan showing fencing, hazards, sanitation location, ingress/egress to public way, and existing utility connection removal locations
- Debris removal plan (by letter or shown as a dumpster location on the site management plan)
- Proof of liability insurance, minimum $300,000 (may be satisfied by a homeowner's policy)
- Signed owner/agent asbestos statement per Colorado Regulation No. 8, Part B — CDPHE requires a Colorado-certified asbestos inspection before demolition/renovation; state/federal rules require the demolition application be postmarked or hand-delivered at least 10 working days before project commencement
- For manufactured/mobile homes: Certificate of Destruction/Removal and Certification of Taxes (Authentication of paid Ad Valorem Taxes) from the County Treasurer/Assessor, per CRS 38-29-204
- If demolition is preparatory to an interior remodel, or removes a portion of a building connected to a remaining structure: an engineer's signed/sealed review confirming the demolition won't harm the remaining structure's vertical, lateral, seismic, or fire-resistive integrity, PLUS a Fire Management Plan describing how fire sprinkler/alarm systems will remain in/out of service or how fire watch will be used
- Possible Historical Review, with permission required prior to permit approval
- Within the City's Commercial Neighborhood (CN), Commercial Old Town (CO), and Yampa Street Commercial (CY) zone districts specifically: a Final Development Plan (FDP) approved by the Department of Planning and Community Development is required BEFORE the Demolition Permit can be issued (Section 709.A.2)
Required documents
- RequiredDe-Construction Permit Application (CityView Portal)
- RequiredConstruction Site Management Plan
- RequiredOwner/Agent Asbestos StatementSigned statement acknowledging Colorado Regulation No. 8, Part B asbestos-inspection requirements
- RequiredProof of Liability Insurance$300,000 minimum
- OptionalFinal Development Plan (FDP)Required only within the CN, CO, and CY zone districts, approved by Planning prior to Demolition Permit issuance
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| De-Construction/Demolition Permit Fee | $125.00 | RCRBD Permit Fee Schedule-Policies |
| Administration fee (permits with no pending construction permit) | $30.00 | Per RCRBD's De-Construction Permit Application and Policy document |
| Fire review fee (within Steamboat Springs Rural Fire Protection District) | $25.00 additional | — |
EV Charger / EVSE Permit
VerifiedThe Routt County Regional Building Department (RCRBD), which administers all building/electrical permits within Steamboat Springs city limits, has no dedicated electric-vehicle-charging-station permit or fee line. An EV charger installed as standalone electrical work (not part of a larger Building Permit) is billed under RCRBD's flat Electrical Alteration Work fee — the same $100.00 residential / $125.00 commercial flat fee documented in the Electrical Permit entry — rather than a distinct EV/EVSE dollar figure; this flat fee is a real, currently-published RCRBD fee-schedule line item and is the governing charge for an EV charger circuit. Steamboat Springs' population exceeds the 10,000-resident municipal threshold in Colorado HB24-1173 (effective 8/7/2024), meaning the City is a 'covered municipal permitting agency' required to have adopted, by 12/31/2025, either the state's model EV-charger permit code, its own objective EV-charger permitting standards, or an affirmation of its existing review process. The City's 2026 building-code-adoption ordinance (amending RMC Ch. 5) adopts the 'State of Colorado Model Electric and Solar Ready Code' as part of its 2021 IBC/IRC package, but that is a construction wiring-readiness code, not confirmation of which HB24-1173 land-use permitting compliance path (model code / custom standards / opt-out) the City selected — no land-use ordinance or RCRBD policy update naming an EV-charger-specific review timeline is published.
Verified 2026-07-20 · Source
Requirements
- EV charger circuit/panel work performed as PART OF an issued Building Permit is exempt from the standalone electrical fee, provided the Building Permit application included the electrical labor/material cost in its valuation — same rule as this file's Electrical Permit entry
- Standalone EV charger electrical work (not associated with a Building Permit) is billed under RCRBD's flat Residential ($100) or Commercial ($125) Electrical Alteration Work fee
- Engineered electrical plans required only if the residential electrical service is 400 AMP or larger, or for commercial/multi-family projects — same threshold as general electrical work
- All applications submitted electronically via the CityView Portal
- Steamboat Springs (population over 10,000) is a 'covered municipal permitting agency' under Colorado HB24-1173; the City's 2026 building-code ordinance adopts the state's Model Electric and Solar Ready Code for new construction wiring readiness, but no public confirmation of RCRBD/the City's chosen HB24-1173 land-use permitting compliance path (model code, custom standards, or opt-out) is published — including in RCRBD's fee schedule, its time-frames document, and the City's ordinance library
Required documents
- RequiredElectrical Permit Application (CityView Portal)No dedicated EV/EVSE checkbox exists; filed as standard electrical alteration work
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Residential Building Electrical Alteration Work (EV charger circuit, not associated with a Building Permit) | $100.00 | RCRBD Permit Fee Schedule-Policies — flat fee, not valuation-based; no dedicated EV/EVSE fee line exists. Re-confirmed live 2026-07-20. |
| Commercial Building Electrical Alteration Work (EV charger circuit, not associated with a Building Permit) | $125.00 | RCRBD Permit Fee Schedule-Policies. Re-confirmed live 2026-07-20. |
Commercial Building Permit (New Construction, Additions & Alterations)
VerifiedRequired for new commercial/industrial buildings, commercial additions, and alterations to existing commercial buildings within Steamboat Springs city limits. Administered by RCRBD under the exact same 'Building Permit' application, valuation-based fee table, and CityView system used for residential permits — RCRBD's own fee schedule confirms one shared valuation table for all building types, not a separate commercial rate — but commercial scope triggers additional mandatory submittals (Civil Plans, Landscape Plans, Construction Specifications, mandatory engineered electrical/mechanical/plumbing plans with no service-size exemption) not required for single-family/duplex residential work, plus a longer review track for buildings over 10,000 sq ft.
Verified 2026-08-02 · Source
Requirements
- Civil Plans required for all new commercial projects, covering grading, drainage, storm water, traffic, access, driveways, roadways (private and public), sidewalk, curb and gutter, parking, and related project information
- Site Plan required for all new commercial/industrial buildings, exterior expansions to an existing commercial/industrial building or its parking, and any Change of Occupancy Permit application
- Landscape Plans required for all new commercial buildings or additions (contact the Planning Department per jurisdiction for specifics on whether they apply to a given project)
- Construction Specification manuals required on all new commercial projects, as well as additions and large alterations
- Engineered electrical plans (one-line service diagram, electrical load calculation, service grounding detail, panel schedules and locations, equipment specs/locations/disconnecting means) are REQUIRED for all new commercial construction and commercial additions/alterations — unlike single-family/duplex residential, there is no electrical-service-size exemption threshold for commercial work; one-line diagrams and load calculations are required for both new commercial services and alterations to existing services
- Mechanical Plans and Plumbing/Fuel Gas Plans required for all new commercial construction and additions/alterations to existing commercial buildings; the Building Department may also request them on other projects if determined necessary to complete review
- Routt County follows Colorado DORA (Department of Regulatory Agencies) regulations for when a Licensed Mechanical or Plumbing Engineer must prepare commercial plans for new construction, additions, alterations, change of occupancy, or equipment replacement — only the exemptions in the DORA handbook are allowed
- Heat Load Calculations required for new commercial buildings or additions onto existing buildings (may be a Deferred Submittal item required prior to issuance of the sub-permit)
- Structural Plans, Soils Report, and Architectural Plans (Code Analysis, Floor Plan, Egress Plan, Section Views, Elevation Views, Energy Code Compliance details) required on the same basis as new residential construction
- Same Table R301.2(1) climatic/geographic design criteria and site-specific Ground Snow Load Map lookup apply to commercial construction as to residential (115 mph ultimate design wind speed, Seismic Design Category C for IRC-governed structures, 48-inch minimum frost line depth, Case Study Area snow load requiring a parcel-specific lookup)
- Class A roof covering required city-wide under the amended IWUIC Section 504.2, same as residential, subject to the same narrow Historic Registered Property/HPC-review exception
- Commercial kitchens serving the public (and Day Care/School projects) require detailed kitchen drawings showing the location of all fixtures, appliances, and cooking units, reviewed by the Routt County Environmental Health Department for CDPH regulations; Commercial Pool and Spa permits are separately reviewed by Environmental Health for CDPH regulations
- City of Steamboat Springs Planning Department reviews all Building Permit applications, including commercial, for planning/zoning compliance in parallel with RCRBD's building review; the City Engineering Division separately reviews work in the public right-of-way, drainage/storm water plans, sidewalks, and private/public street and driveway access
- All applications and plans submitted electronically only through the CityView Portal — RCRBD does not accept paper submittals
Required documents
- RequiredBuilding Permit Application (CityView Portal)Electronic submittal only, via cityview.steamboatsprings.net/portal
- RequiredCivil PlansGrading, drainage, storm water, traffic, access, driveways, roadways, sidewalk, curb/gutter, parking
- RequiredSite Plan
- RequiredLandscape PlansRequired for new commercial buildings or additions; confirm applicability with the Planning Department
- RequiredStructural PlansReferencing the Soils Report and site-specific Ground Snow Load values
- RequiredArchitectural PlansCode analysis, floor plan, egress plan, sections, elevations, energy code compliance details
- RequiredEngineered Electrical PlansMandatory for all new commercial construction and commercial additions/alterations — no service-size exemption unlike residential
- RequiredMechanical Plans
- RequiredPlumbing/Fuel Gas Plans
- RequiredConstruction Specifications
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Building Permit Fee (same valuation-based schedule used for all building types) | $21.15 minimum, scaling per the same valuation tiers used for residential in the RCRBD Permit Fee Schedule-Policies | RCRBD's own fee schedule PDF (Building Department Permit and Plan Review Fees, pages 1-2) publishes an identical valuation table for the unincorporated county AND for the City of Steamboat Springs… Show full citationHideRCRBD's own fee schedule PDF (Building Department Permit and Plan Review Fees, pages 1-2) publishes an identical valuation table for the unincorporated county AND for the City of Steamboat Springs section, and states the fee is 'based upon the Valuation of Work to be Permitted...for all building, electrical, mechanical and plumbing trades' — there is no separate commercial-only rate table. |
| Plan Review Fee | 65% of the Building Permit Fee | Paid at application submittal, before plan review begins |
| Mandatory Routt County Use Tax Fee | (Total Valuation x 0.5) x 1% | Applies in all RCRBD jurisdictions including Steamboat Springs |
| City of Steamboat Springs Use Tax | (Total Project Valuation x 0.5) x 4.5% | Applies only inside City limits, in addition to the countywide Use Tax Fee |
| City of Steamboat Springs Excise Tax | Total Project Valuation x 1.2% | Applies only inside City limits |
Tenant Improvement / Tenant Finish Permit (Commercial Interior Alteration)
VerifiedRequired for interior build-out or alteration of existing commercial tenant space in Steamboat Springs (for example, finishing a new retail, restaurant, or office tenant space within an existing commercial shell). Filed under RCRBD's same Building Permit application and valuation-based fee table as other commercial work, but distinguished by a specific engineered-electrical-plan exception for tenant finishes reusing existing electrical conditions, and by generally falling under RCRBD's lighter interior-alteration review track when the project does not change the building footprint.
Verified 2026-08-02 · Source
Requirements
- Engineered electrical plans (one-line service diagram, load calculation, grounding detail, panel schedules, equipment specs) are required for tenant finishes UNLESS the tenant finish is utilizing existing electrical conditions — in that case the applicant must note this at application and provide documentation showing the existing electrical conditions
- Any proposed alteration to existing branch circuitry, including re-location of lighting or receptacles, must still be noted in the application even when claiming the existing-conditions exception; RCRBD may require a full electrical submittal or electrical 'as-built' drawings at any time prior to approval of the final electrical inspection
- Interior renovations/alterations that do NOT change the building footprint (which covers most tenant finish work) fall under RCRBD's initial 5-business-day review track
- Significant Residential/Commercial interior alterations involving a complete gut/remodel of the existing space, a change in occupancy use affecting zoning requirements, significant structural alterations, or significant Fire Alarm/Sprinkler System changes are explicit exceptions that may increase review time beyond 5 business days — RCRBD does not publish a fixed replacement figure for these exceptions
- Mechanical Plans and Plumbing/Fuel Gas Plans may be required for tenant-finish work, since RCRBD requires them for 'alterations to existing commercial buildings' generally and may additionally request them on any project if determined necessary to complete review
- A Change of Occupancy Permit Application (if the tenant finish changes the space's occupancy classification) requires its own Site Plan submittal
- Routt County follows Colorado DORA regulations for when a Licensed Mechanical or Plumbing Engineer must prepare plans on commercial buildings for alterations or change-of-occupancy permits — only the exemptions in the DORA handbook are allowed
- Tenant-finish work involving a commercial kitchen build-out serving the public requires detailed kitchen drawings reviewed by the Routt County Environmental Health Department for CDPH regulations
- All applications and plans submitted electronically only through the CityView Portal
Required documents
- RequiredBuilding Permit Application (CityView Portal)
- OptionalEngineered Electrical PlansRequired unless the tenant finish qualifies for the existing-electrical-conditions exception
- OptionalExisting Electrical Conditions DocumentationRequired only if claiming the engineered-electrical-plan exception for a tenant finish reusing existing electrical conditions
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Building Permit Fee (same valuation-based schedule used for all building types) | $21.15 minimum, scaling per the same valuation tiers used for residential and new commercial construction in the RCRBD Permit Fee Schedule-Policies | Applies when the tenant finish is filed as a Building Permit based on the value of work to be permitted. Show full citationHideApplies when the tenant finish is filed as a Building Permit based on the value of work to be permitted. If electrical/plumbing/mechanical trade work is instead filed as standalone trade permits not associated with a Building Permit, RCRBD's flat Commercial Building Electrical/Plumbing/Mechanical Alteration Work fee of $125.00 per trade applies instead (see this file's Electrical, Plumbing, and Mechanical/HVAC Permit entries). |
| Plan Review Fee | 65% of the Building Permit Fee | — |
| Mandatory Routt County Use Tax Fee | (Total Valuation x 0.5) x 1% | — |
| City of Steamboat Springs Use Tax | (Total Project Valuation x 0.5) x 4.5% | — |
| City of Steamboat Springs Excise Tax | Total Project Valuation x 1.2% | — |
Sign Permit
VerifiedCity of Steamboat Springs Community Development Code (CDC) Article 5 (Signs) sets sign design/dimensional standards; CDC Article 7, Section 711 (“Sign Permit”) sets the permit process. A Sign Permit is issued by the City's Planning and Community Development Department (not the Routt County Regional Building Department) for placement or construction of a permanent, historic, or temporary sign, except as exempted, limited, or prohibited in CDC Section 504. Three permit types are established: Permanent Sign Permit, Temporary Sign Permit, and Historic Sign Permit. If the sign is a freestanding structure requiring structural review, a separate RCRBD Building Permit (valuation-based) is also required for the structural work.
Verified 2026-08-14 · Source
Requirements
- A Sign Permit is required for any placement or construction of a permanent, historic, or temporary sign except as exempted, limited, or prohibited in CDC Section 504, including erection, alteration, installation, relocation, reconstruction, enlargement, lighting, addition of color, color differentiation, or display of a sign not previously visible, and painting/application of wall or window signs, per CDC §711.A.1
- A Sign Permit is also required for any sign approved by Minor or Major Adjustment, any sign included in a Sign Plan, alterations to a sign inconsistent with sign maintenance (CDC §508.D), and any addition/modification of a differentiated background, per CDC §711.A.1
- Three Sign Permit types are established for review purposes: Permanent Sign Permit, Temporary Sign Permit, and Historic Sign Permit, per CDC §711.A.2
- Review is prior to or concurrent with review of a building permit, if applicable, and may be concurrent with Sign Plan review, if applicable, per CDC §711.B
- A Permanent Sign Permit approval remains effective for one year from the date of approval; a Temporary Sign Permit remains effective for the term specified on the permit, per CDC §711.D
- Certain sign types are exempt from a Sign Permit and from all Article 5 standards, as listed in CDC §504
- If the sign is a structure requiring structural design (e.g., a freestanding monument or pole sign), Structural Plans are also required and a separate RCRBD Building Permit must be obtained, with the standard RCRBD valuation-based building permit fee applying in addition to the City's Sign Permit fee
Required documents
- RequiredSign Permit ApplicationSubmitted to the City of Steamboat Springs Planning and Community Development Department
- OptionalStructural Plans (if applicable)Required from the Routt County Regional Building Department for freestanding/structural signs, in addition to the City's Sign Permit
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Sign Permit (City Planning Dept.) | $150 for one permit covering up to 4 signs; additional signs $50 each | City of Steamboat Springs Development Application Fee Schedule, effective June 17, 2024. |
| Temporary Sign Permit | $50 for one permit covering up to 4 occasions | City of Steamboat Springs Development Application Fee Schedule, effective June 17, 2024. |
| Sign Plan / Sign Plan Amendment / Article 5 Alternative Compliance | Sign Plan $375; Sign Plan Amendment $100; Article 5 Alternative Compliance $50 | City of Steamboat Springs Development Application Fee Schedule, effective June 17, 2024. A Major Adjustment involving a sign is $1,050. |
| RCRBD Building Permit (structural signs only) | RCRBD's combined fee schedule has no separate sign line item; Show full citationHideRCRBD's combined fee schedule has no separate sign line item; a structural sign is billed under RCRBD's standard valuation-based Building Permit fee table (e.g., $1.00-$500 valuation = $21.15) in addition to the City's Sign Permit fee above. Contact RCRBD at 970-870-5566 for a valuation-specific quote. |
Fire Sprinkler / Fire Alarm System Permit
VerifiedFire sprinkler, alarm, commercial kitchen hood, and Bi-Directional Amplifier (BDA) permits within Steamboat Springs city limits are issued directly by Steamboat Springs Fire Rescue (SSFR) — operationally the City's own fire department (Fire Chief and Fire Marshal on City staff) that also serves the separate Steamboat Springs Area Fire Protection District (SSAFPD) under a 2001 intergovernmental agreement. Per RCRBD's own process documentation, 'All Fire Sprinkler/Alarm Permit applications and plans shall be submitted directly to the Fire Department for review and permitting,' separate from the Routt County Regional Building Department's general building permit intake. SSFR's Fire Prevention Services issues the permit for installing, adding to, or modifying a fire alarm system, sprinkler system, or commercial kitchen hood system.
Verified 2026-08-14 · Source
Requirements
- A Fire Prevention Services permit is required for installing, adding to, or modifying a fire alarm system, sprinkler system, or commercial kitchen hood system, per the City's Fire Prevention permit FAQ
- All Fire Sprinkler/Alarm Permit applications and plans are submitted directly to Steamboat Springs Fire Rescue (not to RCRBD) for review and permitting, per RCRBD's City of Steamboat Springs Permit Application Plan Review Processes and Time-Frames document
- Significant changes to a Fire Alarm/Sprinkler System are flagged in RCRBD's building-permit process documentation as a factor that can move an associated building permit out of the standard expedited review tier
- Permit and plan-check fees are valuation-based, using SSFR's 2025 Fire EMS Department Fees base-permit-fee-plus-additional-per-$1,000-valuation table
- A Plan Check Fee equal to 72% of the calculated Permit Fee (base + additional) is charged in addition to the permit fee itself
Required documents
- RequiredFire Sprinkler/Alarm Permit Application and PlansSubmitted directly to Steamboat Springs Fire Rescue, Fire Prevention Services, for review and permitting
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| Sprinkler, Alarm, Hood & BDA Permit Fee (valuation-based) | $1-$2,000 valuation: $55 base, $0/additional $1,000; $2,001-$25,000: $76.18 base, $15.40/additional $1,000; $25,001-$50,000: $430.37 base, $11.11/additional $1,000; $50,001-$100,000: $708.13 base, $7.77/additional $1,000; $100,001-$500,000: $1,093.13 base, $6.16/additional $1,000; $500,001-$1,000,000: $3,557.13 base, $5.23/additional $1,000; $1,000,001+: $6,169.63 base, $4.02/additional $1,000 | Steamboat Springs Fire Rescue / City of Steamboat Springs 2025 Fire EMS Department Fees. Noted on the fee sheet: 'No increase in Sprinkler, Alarm & Hood fees in 2025.' |
| Sprinkler, Alarm, Hood & BDA Plan Check Fee | 72% of the calculated Permit Fee (base + additional, from the table above) | Charged in addition to the permit fee itself, per SSFR's 2025 Fire EMS Department Fees. |
Change of Use / Change of Occupancy
VerifiedThe City of Steamboat Springs Community Development Code (CDC) does not establish a standalone, dedicated 'Change of Use Permit' or 'Change of Occupancy Permit' as its own permit type with its own application, fee schedule, or SLA — confirmed by full-text review of the current CDC (Version 7) for 'change of use,' 'change of occupancy,' and 'Certificate of Occupancy.' Instead, a change of occupancy/use is handled as an application category within the Routt County Regional Building Department's (RCRBD) standard Building Permit process, with the Certificate of Occupancy itself issued by RCRBD (defined in CDC Article 8 as 'a certificate issued by the Routt County Regional Building Department upon completion of activities performed in compliance with a building permit or other permit issued by the Building Department'). The CDC uses 'change of use' narrowly in two contexts only: (1) manufactured home park conversions, which require Conditional Use approval and a Conversion Impact Report under CDC §§707.A and 730; and (2) nonconforming exterior lighting, where 'any change in use or alteration to a structure' triggers compliance review under CDC §405.E.
Verified 2026-08-14 · Source
Requirements
- No dedicated Change of Use or Change of Occupancy Permit exists in the CDC; a change of occupancy/use rides on RCRBD's standard Building Permit application, per RCRBD's City of Steamboat Springs Permit Application Plan Review Processes and Time-Frames document
- 'Change in occupancy use that may affect zoning requirements' is listed by RCRBD as a factor that can move a project beyond its standard 5-day expedited building-permit review tier
- 'Change of Occupancy Permit Application' is listed among the project types requiring a Site Plan submittal to RCRBD
- Colorado's engineered-plan requirement (4 CCR 730-1) applies to change-of-occupancy permits the same as it does to new construction, additions, and alterations, per RCRBD's process document
- The Certificate of Occupancy — issued by RCRBD upon completion of activities performed in compliance with a building permit or other Building Department permit — is the operative document confirming an authorized use/occupancy, per CDC Article 8 definitions
- A narrow, CDC-defined 'change of use' mechanism exists only for manufactured home park conversions (Conditional Use approval plus a Conversion Impact Report, CDC §§707.A, 730) and as a compliance trigger for nonconforming exterior lighting (CDC §405.E) — neither is a general-purpose commercial/residential change-of-use permit
Required documents
- RequiredBuilding Permit Application (with Change of Occupancy noted)Submitted to RCRBD; a change of occupancy is processed as a category within the standard Building Permit application rather than a separate permit form
Fee schedule
| Fee type | Amount | Notes |
|---|---|---|
| No standalone Change of Use / Change of Occupancy fee | Neither the City's Development Application Fee Schedule nor RCRBD's Permit Fee Schedule-Policies PDF publishes a separate 'Change of Use' or 'Change of Occupancy' fee line item; Show full citationHideNeither the City's Development Application Fee Schedule nor RCRBD's Permit Fee Schedule-Policies PDF publishes a separate 'Change of Use' or 'Change of Occupancy' fee line item; the associated work is billed under RCRBD's standard valuation-based Building Permit fee. Contact RCRBD (970-870-5566 / Building@co.routt.co.us) or the City's Planning and Community Development Department (970-871-8258) to confirm what fee applies to a specific change of occupancy. |
Sources & verification
Verified against official sources. Last reviewed 2026-07-06.
Fee schedules
Applications & forms
Checklists & handouts
Online permit portal
Codes & ordinances
Department & other records
Fees, timelines, and adopted codes are researched from each jurisdiction's published records — see how we verify. Requirements change and vary by project, so always confirm the current details with the Steamboat Springs building department before you submit. PermitBase is an independent reference and is not affiliated with any government agency.