Springville building permits

Requirements

• New single-family residential construction
• Additions or structural alterations to existing residential structures
• Building designed to the 2021 IRC (International Residential Code) per Springville Residential Building Permit Checklist (July 2023)
• Planning & Zoning and Storm Water pre-approval through My City Inspector required before Building Division review begins
• Payment of required fees before application and plans are reviewed

Required documents

• RequiredBuilding Permit ApplicationCompleted and signed building permit application, submitted via My City Inspector (springville.mycityinspector.com).
• RequiredPlat or Site PlanShows irrigation ditches, utility locations as built, water meter and pressurized-irrigation (PI) location (cannot be in the driveway), contours for sloping lots, and retention if any.
• RequiredFooting and Foundation Plan, Floor Plans, Elevations, Wall Cross SectionElevations must show cross sections with overall height from natural grade; finish and natural/existing grade in relation to curb height, finish floor height, retaining walls, flood plains, and fault lines (if applicable).
• RequiredPlumbing, Mechanical, and Electrical PlansPlumbing and mechanical layouts, electrical plans, diagram of gas line (size, length, BTU of appliances).
• RequiredEnergy Analysis / Envelope DescriptionFor energy code compliance, per Springville Residential Building Permit Checklist.
• RequiredManual D, J, and S ComplianceStatic pressure design and HVAC specifications.
• RequiredSoils Geotechnical ReportIndicating allowable bearing pressure, water table depth, and foundation drainage requirements. Slope stabilization required for sloping lots and retaining walls.
• OptionalEngineering (if required)Wet-stamped calculations; truss manufacturer's detail sheet if applicable; retaining wall construction endorsement from a structural engineer if used.
• OptionalOwner/Builder CertificationSigned and notarized, if the owner (not a licensed contractor) is performing the work.

Fee schedule

Requirements

• Interior remodel: permit needed if adding/removing structural components, or changing electrical, HVAC, or plumbing systems, per Springville Building FAQ
• Basement finish: changing an unfinished basement to a habitable location, or adding electrical, plumbing, or heating systems, requires a permit per Springville Basement Improvement Permit Checklist (July 2023)
• Building shall be designed to the 2021 IRC and State Amendments

Required documents

• RequiredBuilding Permit ApplicationCompleted application, available at Springville City offices or online at springville.org/permits.
• RequiredFloor Plan of Proposed AreaLabel all areas for intended use.
• OptionalSite Plan (if walk-out included)Shows house location on property, location of improvements, and setback measurements.
• OptionalEngineering for Beams Replacing Bearing WallsRequired when removing or altering load-bearing walls.
• RequiredWindow and Door Locations, Mechanical Room LocationShow all window/door locations and location of mechanical room/equipment.
• OptionalElectrical/Gas InformationDepending on scope of work.
• OptionalContractor Information or Owner/Builder CertificateSigned and notarized if owner-performed.

Fee schedule

Requirements

• New electrical circuits, wiring, or service changes
• Electrical work must be permitted and paid for separately from the building permit — 'Electrical, Plumbing, or Mechanical Permits need to be applied and paid for separately by each Subcontractor'
• Building/electrical work designed to the 2021 IRC and statewide 2023 NEC

Required documents

• RequiredTrade Permit ApplicationSubmitted via My City Inspector (springville.mycityinspector.com), separately from the building permit.
• OptionalElectrical PlansRequired as part of the plan set when electrical is part of a building permit submittal; a standalone electrical trade permit is required in addition.

Fee schedule

Requirements

• New plumbing fixture installations, water heater replacement, water/sewer line work
• Plumbing Permits need to be applied and paid for separately by each Subcontractor
• Underground plumbing and sewer lateral inspections require water testing per Springville Residential Building Permit Checklist

Required documents

• RequiredTrade Permit ApplicationSubmitted via My City Inspector, separately from the building permit.
• OptionalPlumbing PlanPlumbing layout as part of the overall plan set when plumbing is part of new construction.

Fee schedule

Requirements

• Furnace or A/C replacement or installation
• Ductwork installation or modification
• Mechanical Permits need to be applied and paid for separately by each Subcontractor when part of new construction

Required documents

• RequiredTrade Permit ApplicationSubmitted via My City Inspector.
• OptionalEquipment SpecificationsManufacturer data for furnace/AC unit being installed or replaced.

Fee schedule

Requirements

• Roof replacement or re-roofing — permit required per Springville Building FAQ ('Roof - Yes' under 'Do I need a permit to build?')
• Building shall be designed to the 2021 IRC

Required documents

• RequiredPermit ApplicationScope of work, square footage, material specifications, submitted via My City Inspector.

Fee schedule

Requirements

• Site has DRC (Development Review Committee) review and approval before the building permit can be accepted
• All outside fees (irrigation company fees, SWPPP fees, etc.) paid before permit submission
• Completed Building Permit application
• Plan check fee due in FULL at time of permit submission
• Water shares tendered, if not previously done with the development
• Preconstruction meeting required for all multi-family and commercial projects prior to construction start

Required documents

• RequiredPlat or Site Plan (DRC-Approved)Per Springville Commercial Building Permit Checklist (2026).
• RequiredCover Sheet (Code Analysis)Design information showing code analysis.
• RequiredStructural Design / Architectural DrawingsWith appropriate engineering endorsements.
• RequiredElectrical / Mechanical / Plumbing PlansWith appropriate professional endorsements, including an Electrical Service Information Request form.
• OptionalTruss Engineering and LayoutFrom the truss manufacturer, where applicable.
• RequiredHeating/Cooling Load Calculations and ComCheck/ASHRAE 90.1 ComplianceDuct design and energy code compliance documentation.
• RequiredEgress Components with Load CalculationsPer Springville Commercial Building Permit Checklist.
• RequiredADA Compliance (2009 ANSI A117.1)Accessibility compliance documentation.
• OptionalFire Protection Systems / Fire-Resistive ConstructionAs applicable to occupancy and construction type.
• RequiredGeotechnical ReportPer Springville Commercial Building Permit Checklist.
• RequiredConstruction ValuationA bid may be submitted for valuation purposes.

Fee schedule

Requirements

• Any structural, electrical, plumbing, or HVAC change to the tenant space
• Code Analysis from an Architectural Design Professional addressing occupant load, exiting, possible fire-resistive construction, number of restrooms, and ADA accessibility accommodations
• Completed and signed Building Permit application
• Plan check fee due in FULL when the permit application is submitted
• Contractor information or a signed Owner/Builder Certificate

Required documents

• RequiredBuilding PlansDrawn to scale, endorsed and signed by an architect and all other professional designers.
• RequiredCode Analysis SheetOccupancy group, type of construction, occupant load, and allowable area.
• RequiredFloor PlanDimensions, exits, occupancy types and use, ADA provisions, equipment/shelving/counter locations, occupant load, restroom locations, adjacent business uses; wall section with stud size, height, spacing, insulation, fire separation, gypsum board, and structural connections.
• RequiredPlumbing PlanPlumbing schematic and type of material used.
• RequiredMechanical PlanMechanical schematic, size of ducts, location of return air ducts and fire dampers, combustion air, HVAC units, and kitchen hoods.
• RequiredElectric PlanElectrical locations, calculations, emergency/exit lighting, and panel schedules.
• RequiredEnergy Compliance CalculationsComCheck or equivalent.

Fee schedule

Requirements

• Completed and signed building permit application including licensed installer information and system valuation (labor and materials)
• System shall be designed to the current statewide-adopted IRC and NEC editions (2021 IRC, 2023 NEC per Utah Code § 15A-2-103 as of 2026-07-19 — Springville's own Solar Permit Process document is dated 2019 and still cites the outdated '2015 IRC and 2017 NEC,' which the current statewide statute supersedes)
• All electrical equipment must carry UL listing
• Plan check deposit required (paid in full at submission) for systems larger than 4 kW
• Springville Power requires a completed Customer-Owned Generation Agreement and Customer-Owned Generation Application before installation of the utility meter
• Springville Power Standards require a dedicated production meter as part of the Customer-Owned Generation Agreement
• Payment of completion and performance bonds required when picking up the building permit

Required documents

• RequiredBuilding Permit ApplicationCompleted and signed, including licensed installer information and system valuation (labor and materials); submitted via My City Inspector (springville.mycityinspector.com). Per the official Solar Permit Process document: 'Permits will not be accepted as incomplete submissions.'
• RequiredSite PlanModule locations, structures, location of equipment, location of existing vents and exhaust outlets, and fire access setbacks from ridges, eaves, and valleys.
• RequiredConstruction Drawings and One-Line DiagramOne complete electronic set (PDF) showing equipment locations, conductor sizes and types.
• RequiredInter-connection Location DetailsDisconnect location and size of overcurrent protection.
• RequiredSystem Sizing CalculationsOvercurrent protection sizing, conductor sizing, and maximum allowed system-based rating of equipment.
• RequiredLabels, Placards, and Equipment PhotosLocation of labels/placards with an appropriate list of labels provided, plus pictures of existing service equipment showing rating size and interconnection breaker location.
• RequiredRacking Support Locations and Technical Data SheetsTechnical data for racking, inverters, micro-inverters, optimizers, rapid shutdown devices, flashings, supports, junction boxes, combiners, modules, and service equipment (if upgrading).
• RequiredEngineering LetterClearing existing conditions of additional loading on the truss or rafter system.
• RequiredCustomer-Owned Generation Agreement and Application (Springville Power)Required by Springville City Power before installation of the utility production meter — scheduled by calling Springville City Power at (801) 489-2750 (7 am-3:30 pm) for an in-person appointment to sign required documentation.

Fee schedule

Requirements

• Applies to fire alarm systems, fire sprinkler systems, and hood extinguishing systems, plus related preliminary site plans, fire department apparatus accessibility, fire flow requirements, and new fire hydrant placement
• Plans reviewed directly by the Springville City Fire Marshal, separate from the Building Division's plan review
• Plans must be submitted electronically by email (via the Fire and Rescue department's 'Email Plans' link)
• Construction permits are issued only upon the Fire Marshal's approval of submitted plans
• Inspections must be requested at least two days before the intended inspection date, by phone or email to the Fire Marshal
• Inspections are not conducted on Mondays (to accommodate a required 24-hour battery test); Friday inspections are by request only

Required documents

• RequiredFire Sprinkler / Alarm / Hood Plan SubmittalPlans submitted electronically by email directly to the Fire Marshal, per Springville Fire and Rescue's 'Fire Sprinkler, Alarm and Hood Plan Inspections' page — this is separate from the My City Inspector submittal used for the associated building permit.

Fee schedule

Requirements

• Sign shall be designed to the 2021 IBC and 2023 NEC and conform to Title 11-6-310 Springville City Ordinance
• One complete set of electronic construction plans submitted in PDF format via My City Inspector (springville.mycityinspector.com)
• Completed and signed building permit application including licensed installer information and valuation of sign
• Proof of a current Springville City business license
• Engineering (with wet stamp, calculations, and attachment schedule) required if the sign meets or exceeds any of: projects more than 4 inches from wall/structure; exceeds 4 lbs per square foot; stand-off dimension exceeds 2 inches from wall/structure; or exceeds 4 feet in height from grade for a stand-alone sign
• All electrical signs require UL listing as a sign per NEC 600.3
• Permit applications will not be accepted as incomplete submissions

Required documents

• RequiredBuilding Permit ApplicationCompleted and signed, including licensed installer information and valuation of sign; submitted via My City Inspector.
• RequiredSite PlanProperty lines and dimensions, existing and proposed buildings/structures/signs, overhead utility lines, and streets/driveways/parking spaces/landscaping within 20 feet of the property.
• RequiredBuilding ElevationsCross sections with overall height from natural grade and size of sign with dimensions (area, width, height, depth); for individual letters/graphics, dimensions per row including distances between lines of text or graphics.
• RequiredConstruction Drawings, Footing and Foundation PlanIncludes columns, posts, beams, framework, internal bracing, and other applicable construction information.
• RequiredElectrical InformationDisconnect location and size of overcurrent protection.
• OptionalEngineering (if required)Wet-stamped calculations with attachment schedule, required when the sign meets or exceeds specific size/weight/stand-off/height thresholds (see requirements).
• RequiredProof of Current Springville City Business LicenseRequired as part of the submittal.

Fee schedule

Requirements

• Required whenever a unit/building's use changes from its previous use (e.g., storage converted to a print shop), per Springville's Building FAQ and Business Licensing FAQ
• Required before a business may occupy interior space in a shell building that has received only a Certificate of Completion for its exterior structure — the shell permit's plan set does not address interior occupant load, exiting, or use
• Code Analysis from an Architectural Design Professional addressing occupant load, exiting, possible fire-resistive construction, number of restrooms, and ADA accessibility accommodations
• Floor plan showing any modifications planned for the space
• Application submitted via My City Inspector (springville.mycityinspector.com) after creating an account; 'change of use' selected as the Type of Permit

Required documents

• RequiredCode Analysis (Architectural Design Professional)Per Springville's Business Licensing FAQ: 'The most important information needed in this application is a Code Analysis from an Architectural Design Group.' Addresses occupant load, exiting, possible fire-resistive construction, number of restrooms, and ADA accessibility accommodations.
• RequiredFloor PlanShows any modifications planned for the space. Per Springville's Business Licensing FAQ, it 'can be hand drawn and does not have to be scale, but must include overall measurements, use of each room, and measurement of each room.'
• RequiredSketch of Existing Site PlanUploaded with the online application alongside the floor plan sketch, per Springville's Business Licensing FAQ instructions for starting a change-of-use application.
• RequiredMy City Inspector Account and ApplicationCreated via the 'Create an Account' button on the Building Division page, then submitted at springville.mycityinspector.com with 'change of use' selected as the Type of Permit.

Fee schedule

Requirements

• Installation of a Level 2 or DC fast EV charger (EVSE) at a residential or commercial property
• Electrical, Plumbing, or Mechanical Permits must be applied for and paid for separately by each Subcontractor, even on new residential building permits
• Governed by the 2023 NEC (Utah statewide) and 2021 IRC

Required documents

• RequiredTrade Permit ApplicationSubmitted via My City Inspector (springville.mycityinspector.com), separately from any building permit.
• OptionalElectrical PlansCircuit/panel documentation for the EVSE installation, particularly if a service upgrade is involved.

Fee schedule