Gila Bend building permits

Requirements

• Building permit required for new single-family residence construction within Gila Bend town limits
• Plans must comply with the 2006 IRC/IBC as adopted by the Town (§ 150.15, § 150.20) and the Residential Solar Readiness Ordinance (§ 150.04) requiring later-installation provisions for solar water heating and/or solar electric systems unless a complete solar system is installed at construction
• Completed Project Submittal Form/Building Permit Application (including owner information) and Plan Review Fee required at submittal
• Two (2) complete sets of plans; two (2) extra site plans for Engineering review; structural calcs and truss calcs (if applicable, truss calcs can be deferred); two (2) 8.5x11 plot plans
• Seismic Design Category C applies

Required documents

• RequiredBuilding Permit Application / Project Submittal FormTown of Gila Bend Building Permit Application, submitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — New Single Family Residences sectionTown of Gila Bend Community Development checklist specifying required plan sets, site plans, structural/truss calcs, and plot plans
• RequiredSite/Plot Plan (8.5x11, two sets)Lot dimensions, easements, setbacks, and structure locations for Engineering review

Fee schedule

Requirements

• Building permit required for residential additions, alterations, and remodels
• Completed Project Submittal Form and Plan Review Fee required for additions/alterations; four (4) complete sets of plans; two (2) sets of structural calcs and lighting cut sheets if exterior lighting is modified/added
• Residential Additions: Completed Project Submittal Form, Plan Review Fee, two (2) complete sets of plans, two (2) extra site plans for Engineering review, truss calcs if applicable, two (2) 8.5x11 plot plans
• Residential Remodels: Completed Project Submittal Form, Plan Review Fee, two (2) complete sets of plans
• Patio additions use the Town's Patio Addition Package examples showing easement, property line, and building setback illustrations

Required documents

• RequiredBuilding Permit Application / Project Submittal FormSubmitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — Additions/Alterations, Residential Additions, and Residential Remodels sectionsTown of Gila Bend Community Development checklist
• OptionalPatio Addition 1 Package / Patio Addition 2 PackageTown of Gila Bend example diagrams of easement, property lines, and building setbacks for patio cover submittals

Fee schedule

Requirements

• Electrical permit required for utility clearances (electric/gas), electrical panel and service work, generator transfer-switch installations, and other hard-wired electrical work
• Governed by the 2005 NEC as adopted by the Town (§ 150.16)
• MEP-only submittals: Completed Project Submittal Form, two (2) complete sets of plans (four (4) sets if exterior lighting is added/modified or roof-mounted A/C units are added)
• Generator permanent/transfer-switch installations require 2 sets of drawings (one-line electrical diagram with load calculations, plus site plan with generator location, fuel type/capacity, property lines, building locations/dimensions); portable generators plugged directly into appliances do not require a permit
• Special Electrical Inspection Certificate required when electrical construction work is placed under a special inspector employed by the owner/owner's agent, per the Town's adopted electrical code — inspection reports filed with the Building Safety Department

Required documents

• RequiredBuilding/Electrical Permit ApplicationSubmitted to Willdan Engineering/Community Development
• OptionalSpecial Electrical Inspection CertificateTown of Gila Bend form for projects using an owner-employed special inspector for electrical construction; requires Architect/Engineer, Owner, and Building Official signatures at issuance and completion stages
• OptionalGenerator Use & Safety drawingsOne-line electrical diagram with load calculations and site plan (generator location, fuel type/capacity, property lines, building dimensions), per Town Generator Use & Safety guidance

Fee schedule

Requirements

• Plumbing permit required for installation, alteration, or repair of plumbing systems, fixtures, and water heaters
• Governed by the 2006 IPC as adopted by the Town (§ 150.18)
• MEP-only submittals: Completed Project Submittal Form, two (2) complete sets of plans
• Water heater installs (electric or gas) are individually fee-itemized on the Town's fee schedule

Required documents

• RequiredBuilding/Plumbing Permit ApplicationSubmitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — MPE Only sectionTown of Gila Bend Community Development checklist for mechanical/plumbing/electrical-only submittals

Fee schedule

Requirements

• Mechanical permit required for installation, replacement, or relocation of HVAC equipment and ventilation systems
• Governed by the 2006 IMC as adopted by the Town (§ 150.17)
• MEP-only submittals: Completed Project Submittal Form, two (2) complete sets of plans (four (4) sets if adding roof-mounted A/C units)
• Residential and Commercial A/C unit replacement fees are individually itemized on the Town's fee schedule

Required documents

• RequiredBuilding/Mechanical Permit ApplicationSubmitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — MPE Only sectionTown of Gila Bend Community Development checklist for mechanical/plumbing/electrical-only submittals

Fee schedule

Requirements

• Electrical scope: MEP-only submittal — Completed Project Submittal Form and two (2) complete sets of plans (four (4) sets if roof-mounted equipment such as an inverter/combiner enclosure triggers the roof-mounted-equipment plan-set requirement), reviewed against the 2005 NEC as adopted (§ 150.16)
• Structural/racking scope: Residential Building Permit application if roof penetrations or structural modification are involved, reviewed against the 2006 IBC/IRC (§§ 150.15, 150.20)
• If installed at time of new single-family/duplex construction, the complete solar system satisfies (and supersedes) the Residential Solar Readiness Ordinance's later-installation provisions (§ 150.04) — otherwise those later-installation provisions (conduit/piping stub-outs, 80-gallon water heater storage area, dedicated 120V/15A circuit) apply to the new home regardless of whether solar is installed immediately
• No dedicated solar/PV-specific plan-submittal checklist section (unlike the Checklist's dedicated Pools, Mobile Home, or Patio Addition sections) was found published — confirm current submittal expectations directly with Willdan Engineering, BuildingSafetyAZ@willdan.com, 480-489-2463

Required documents

• RequiredBuilding/Electrical Permit Application / Project Submittal FormSame combined form used for other electrical/MEP-only work; no separate solar-specific version is published. Submitted to Willdan Engineering/Community Development.
• RequiredSite/Plot Plan and Electrical One-Line DiagramNot a Town-published solar-specific form; standard electrical plan-review content inferred from the Town's general MEP-only submittal requirements, since no PV-specific checklist is published

Fee schedule

Requirements

• Electrical permit required for a new dedicated EVSE circuit, governed by the 2005 NEC as adopted by the Town (§ 150.16)
• MEP-only submittals: Completed Project Submittal Form, two (2) complete sets of plans
• Special Electrical Inspection Certificate required only if electrical construction work is placed under a special inspector employed by the owner/owner's agent

Required documents

• RequiredBuilding/Electrical Permit ApplicationSubmitted to Willdan Engineering/Community Development. No separate EV-specific application form was found published.

Fee schedule

Requirements

• Building permit required for swimming pool/spa construction
• Pool barrier requirement: perimeter fence/barrier at least 5 feet high, self-closing/self-latching gate hardware, and a configuration that prevents a 4-inch sphere from passing through or under the barrier
• Pools (One Time Only, i.e. custom/non-standard plan): Completed Project Submittal Form, Plan Review Fee, two (2) complete sets of plans, two (2) 8.5x11 plot plans
• Pools (Based on Approved Standard, i.e. a standard plan already on file): Completed Project Submittal Form, two (2) 8.5x11 plot plans only — no separate plan review fee/full plan set required since the standard design is pre-approved

Required documents

• RequiredBuilding Permit Application / Project Submittal FormSubmitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — Pools (One Time Only) and Pools (Based on Approved Standard) sectionsTown of Gila Bend Community Development checklist
• RequiredPool, Spa Barrier GuidelinesReferenced in the Town's Building Safety FAQ as the governing pool-fencing standard

Fee schedule

Requirements

• Completed Project Submittal Form required for demolition of an entire building
• Two (2) 8.5x11 site plans clearly identifying the building to be demolished
• Pedestrian protection may be required, at the plan reviewer's determination
• Interior-only demolition follows the Tenant Improvement submittal requirements instead
• Building moving/relocation: upon compliance with the moving-building provisions, the Building Official inspects the structure and its foundation, and a moving permit is issued if the inspection, photographs, and plat reveal no ordinance violation (§ 151.03)

Required documents

• RequiredBuilding Permit Application / Project Submittal FormSubmitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — Demolition (Entire Building) sectionTown of Gila Bend Community Development checklist
• RequiredSite Plan (8.5x11, two sets)Clearly identifies the building to be demolished

Fee schedule

Requirements

• A building permit is required for any fence that will be over 6 feet in height when finished; fences 6 feet and under do not require a permit
• Swimming pool barrier fences must always meet pool-barrier standards (minimum 5-ft height, self-closing/self-latching gates, 4-inch-sphere test) regardless of the general fence height exemption
• Fee schedule fence line item is captioned 'Fence (over 72in)' — consistent with the 6-foot (72-inch) permit threshold stated in the Building Safety FAQ

Required documents

• RequiredBuilding Permit Application / Project Submittal FormSubmitted to Willdan Engineering/Community Development

Fee schedule

Requirements

• Manufactured Home: Completed Project Submittal Form, three (3) 8.5x11 plot plans, and Zoning Clearance
• Factory Built Buildings (on-site permit): Completed Project Submittal Form and two (2) complete sets of plans bearing the approval of the Arizona State Division of Building Codes
• Grading Only (if site work is needed for placement): Completed Project Submittal Form and two (2) sets of Civil plans showing cut and fill amounts; Building plans must be in for review and Engineering plans must have been through the review process at least once

Required documents

• RequiredBuilding Permit Application / Project Submittal FormSubmitted to Willdan Engineering/Community Development
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — Mobile Home and Factory Built Buildings sectionsTown of Gila Bend Community Development checklist
• RequiredZoning ClearanceRequired for manufactured home placement

Fee schedule

Requirements

• Sign permit required for erection, use, or display of commercial/business signage, submitted on the combined Town of Gila Bend Building Permit Application with the 'Sign' box checked and the form's Signs data block completed (Type, Overall Height, Width, Lighted yes/no, Clearance from ground)
• A sketch showing the sign's locale and setbacks from the highway and property lines must be submitted with the application, per the application form's own instruction
• Must comply with Zoning Ordinance Article VIII District Regulations (§ 16-8-03), which vary by zoning district: Residential Districts limit free-standing signs to 6 ft maximum height and prohibit home-occupation signs; B-1 District limits wall signs to 15% of wall area (100 sq ft max per sign) and one free-standing sign per shopping center/isolated commercial establishment (40 sq ft max, 20 ft max height); B-2 District limits wall signs to 15% of wall area or 300 sq ft (whichever is less) and free-standing signs to 60 sq ft/25 ft height for the first sign per 300 ft of frontage; I-1/I-2 Districts limit wall signs to 20% of wall area and free-standing signs to 60 sq ft/25 ft height; Billboards are restricted to frontage along Interstate 8 and State Highways 84/85 only, capped at 800 sq ft area and 50 ft height, with minimum spacing/setback rules
• General provisions applicable in all districts (§ 16-8-02) include: no illuminated flashing signs (>12 flashes/minute) except limited public-service messages in B-2/I-1/I-2 Districts; illuminated signs within 50 ft of a Residential District lot line must be diffused/indirect; free-standing signs within 25 ft of an intersection must have 12 ft vertical clearance or be under 36 inches tall; temporary construction-site identification signs limited to 65 sq ft; temporary real estate signs for 10+ unit or nonresidential projects limited to 60 sq ft (one per street frontage)
• Interior signs not visible from the exterior of the building are exempt from permit and fee requirements entirely, per Zoning Ordinance § 16-8-02(S)
• Fences 6 ft and under, one-story accessory buildings under 200 sq ft, and other Chapter 150 exemptions documented elsewhere in this file do not apply to signage — sign permitting is governed independently by the Zoning Ordinance's Article VIII, not Chapter 150

Required documents

• RequiredTown of Gila Bend Building Permit Application (Sign)The same combined Town of Gila Bend Building Permit Application used for Bldg/Elec/Mech/Plbg/Combo permits, with the 'Sign' box checked and its dedicated Signs section (Type, Overall Height, Width, Lighted, Clearance from ground) completed. Submitted to Willdan Engineering/Community Development.
• RequiredSketch of sign locale and setbacksSketch showing the sign's location and setbacks from the highway and property lines, per the Building Permit Application's own submittal instruction

Fee schedule

Requirements

• Permit required for installation of a new automatic fire extinguishing system (AFES/fire sprinkler system) or fire alarm system, governed by the 2006 IFC as adopted by the Town (§ 92.01) and reviewed as part of the fire-protection scope of the 2006 IBC (§ 150.15)
• AFES (Fire Sprinkler) plan review is tracked as its own category on the Town's Turn Around Times for Submittals document, distinct from Residential/Commercial/Electrical/Mechanical review
• Underground fire-service piping supplying a sprinkler system is separately tracked under the 'Fire (Underground)' review category on the same document
• New Commercial submittals (checklist category 'NEW BUILDING (Non-Residential)') fold fire-protection system review into the standard four-set plan submittal; fire sprinkler/alarm work in an existing building follows the Tenant Improvements submittal checklist category instead
• Building/fire permit valuation is determined using the same ICC building valuation data table used for general building-permit valuations, per Gila Bend Code of Ordinances § 150.03(B): 'For the purpose of determining the fire permit valuations, the most current building valuation data table ... shall be used to determine the fire permit fee'
• No fire-alarm-specific review-timeline row or fee line item is separately published by the Town — confirmed absent after full-text review of the Fee Schedule, Building Plan Check Submittal Checklist, and Turn Around Times document; a stand-alone fire alarm system is processed under the general Electrical Permit and/or valuation-based Building Permit fee mechanisms documented on this jurisdiction's electrical-permit entry

Required documents

• RequiredTown of Gila Bend Building Permit Application (Combo/Fire scope as applicable)Same combined Town of Gila Bend Building Permit Application used for other permit types. Submitted to Willdan Engineering/Community Development; no separate AFES-specific application form was found published.
• RequiredFire sprinkler/alarm shop drawings and hydraulic calculationsStandard NFPA 13 (sprinkler)/NFPA 72 (alarm) submittal content inferred from the Town's 'AFES (Fire Sprinkler)' review category; no Town-published AFES/alarm-specific submittal checklist section was found
• RequiredBuilding Plan Check Submittal Checklist (rev. 8.6.16) — New Building (Non-Residential) or Tenant Improvements sectionTown of Gila Bend Community Development checklist governing the plan-set quantity for the underlying building scope that the fire-protection system is installed within

Fee schedule

Requirements

• No dedicated Change-of-Use or Certificate-of-Occupancy permit application is published by the Town; a change in use or occupancy of an existing building is processed through whichever underlying permit track applies to the proposed work — Tenant Improvements or New Building (Non-Residential) on the Building Plan Check Submittal Checklist (rev. 8.6.16), or the applicable MEP-only track if the change is limited to systems work
• Per the 2006 IBC as adopted by the Town (§ 150.15), a Certificate of Occupancy is required before a building, structure, or portion thereof may be lawfully used or occupied, and a new Certificate of Occupancy is required whenever the use or occupancy classification of a building changes
• Per the Town's Zoning Ordinance § 16-5-07(A)(2) (Off-Street Parking Requirements), any change of use or occupancy of a building, including additions, that requires additional off-street parking is not permitted until the additional required parking spaces are furnished — this is a zoning-compliance condition attached to the underlying permit, not a separate standalone permit product
• Other permit-type entries in this jurisdiction file already reference the Certificate of Occupancy as the closing step of the standard permit/inspection process (e.g., the plumbing-permit entry notes backflow-preventer certified testing 'prior to Certificate of Occupancy if required'), consistent with there being no separate CO permit product distinct from the underlying building permit's final inspection

Required documents

• RequiredBuilding Permit Application / Project Submittal Form for the underlying scope of workSame combined Town of Gila Bend Building Permit Application used for the New Building (Non-Residential), Tenant Improvements, or other applicable track governing the change of use. No distinct Certificate of Occupancy or Change of Use application form was found published by the Town.

Fee schedule