Sheridan building inspections

Applies to: Change of Occupancy Use Permit (Certificate of Occupancy)

1. 1

   Fire Safety

   Verifies fire-safety compliance of the location prior to occupancy (City Code Section 7-24.1(b))

2. 2

   Building Structure

   Verifies structural/building-code compliance of the location prior to occupancy (City Code Section 7-24.1(b))

3. 3

   Sanitation

   Verifies sanitation compliance of the location prior to occupancy (City Code Section 7-24.1(b))

4. 4

   Zoning

   Verifies the intended use complies with the applicable zoning district prior to occupancy (City Code Section 7-24.1(b))

Applies to: Commercial Tenant Improvement Permit

1. 1

   Framing / Structural

   After framing complete before walls covered

2. 2

   MEP Rough-In

   Mechanical, electrical, plumbing rough-in before walls closed

3. 3

   Fire / Knox Box

   Knox box installation verification (required on all commercial occupancies per local amendment); fire sprinkler/alarm inspections currently routed through the State per City's posted notice

4. 4

   Final / Certificate of Occupancy

   All work complete, ready for occupancy

Applies to: Residential Addition / Remodel Permit

1. 1

   Footing / Foundation (if new footings)

   Before concrete pour, below the 42-inch local frost line

2. 2

   Framing

   After framing complete, before insulation or wall cover

3. 3

   MEP Rough-In

   Electrical, plumbing, mechanical rough-in before walls closed

4. 4

   Final

   All work complete per approved plans

Applies to: Residential Building Permit (New Construction)

1. 1

   Foundation / Footings

   Before concrete pour — footings must extend below the 42-inch local frost line

2. 2

   Framing

   After framing complete, before insulation or wall cover

3. 3

   MEP Rough-In

   Mechanical, electrical, and plumbing rough-in before walls closed

4. 4

   Final

   All work complete, smoke/CO detectors installed, ready for occupancy

Applies to: Deck Permit

1. 1

   Footing

   Pier/footing depth verification below 42-inch frost line, before concrete pour

2. 2

   Framing

   Ledger attachment, joist hangers, structural connections before decking installed

3. 3

   Final

   Guardrails, stairs, and decking complete per approved plans

Applies to: Mechanical / HVAC Permit

1. 1

   Gas Piping Pressure Test

   Required before concealing gas piping — 10 lbs held for 15 minutes on threaded gas piping per local IFGC amendment

2. 2

   Rough-In / Equipment

   Equipment installation and ductwork before walls closed

3. 3

   Final

   Equipment operational, combustion air and venting verified

Applies to: Plumbing Permit

1. 1

   Underground / Under-slab

   Before concrete pour — verify pipe slope, materials, cleanouts

2. 2

   Rough-In

   After pipes installed, before walls closed — includes 5 psi/15-minute air test per local IPC amendment

3. 3

   Final

   All fixtures connected, no leaks, venting verified

Applies to: Electrical Permit

1. 1

   Rough-In

   Wiring and conduit installed before walls closed

2. 2

   Final

   All devices installed, panel labeled, system energized

Applies to: EV Charger / EVSE Permit (Electrical Simple Permit)

1. 1

   Rough-In

   Circuit wiring, conduit, and panel connections before walls are closed, if applicable

2. 2

   Final

   Charger mounted, connections verified, system energized

Applies to: Fire Sprinkler / Fire Alarm / Fire Suppression System Permit

1. 1

   System Rough-In

   Piping, wiring, and device placement before concealment, per approved plans

2. 2

   Final / Acceptance Test

   Functional/acceptance testing of the completed fire alarm, sprinkler, or suppression system per the approved plans and adopted Fire Code

Applies to: Solar PV Permit

1. 1

   Rough Electrical

   Conduit runs, wire sizing, disconnect placement before cover

2. 2

   Final

   All connections and racking/roof penetrations verified, system energized

Final inspection only: Demolition Permit, Roofing Permit (Re-Roof), Sign Permit