Unincorporated Uintah County building inspections

Applies to: Commercial Building Permit

1. 1

   Footing/Setback Inspection

   All property corners correctly marked with lath and ribbon and visible before footing inspection.

2. 2

   Foundation Inspection

   After footing/foundation reinforcement is in place, before concrete pour.

3. 3

   Concrete Slab and Under-Floor Inspection

   After in-slab/under-floor reinforcing steel and building service equipment/conduit/piping are in place, before concrete is placed.

4. 4

   Frame/4-Way Inspection

   After roof deck/sheeting, all framing, fire blocking and bracing are in place, and rough electrical/plumbing/HVAC/gas are tested and approved.

5. 5

   Fire Sprinkler / Fire Alarm Review and Inspection

   For occupancies requiring fire suppression or alarm systems, per the county's Fire District Fees schedule; scheduled separately from the building inspection sequence.

6. 6

   Energy Efficiency (Insulation) Inspection

   Compliance with IRC/IBC energy provisions — envelope insulation R/U value, duct system R value, HVAC and water-heating equipment efficiency.

7. 7

   Final Inspection

   All work required by the building permit is complete; a Certificate of Occupancy is required before the structure may be used or occupied.

Applies to: Commercial Tenant Improvement / Tenant Finish Permit

1. 1

   Rough-In (Framing/Electrical/Plumbing/Mechanical)

   Scope-dependent rough-in inspection of new interior partitions, wiring, piping, or ductwork before walls are closed.

2. 2

   Remodel Fire Review / Inspection

   For occupancies requiring fire suppression or alarm review on remodel scope, per the county's Fire District Fees schedule ($70 review, $60 inspection).

3. 3

   Energy Efficiency (Insulation) Inspection

   Where the scope affects building envelope insulation or mechanical/water-heating efficiency.

4. 4

   Final Inspection

   All work required by the building permit is complete; a Certificate of Occupancy or occupancy sign-off is required before the space may be used.

Applies to: Swimming Pool Permit

1. 1

   Excavation / Steel

   Pool shell excavation, rebar, and plumbing before gunite/shotcrete or liner installation

2. 2

   Electrical / Bonding

   Pool bonding grid, equipment connections, GFCI protection per NEC Article 680

3. 3

   Barrier

   Pool fence/barrier per adopted IRC/ISPSC, self-closing/self-latching gates

4. 4

   Final

   Pool complete, filled, equipment operational, all barriers in place

Applies to: Electrical Permit

1. 1

   Construction Power Inspection

   Pedestal or meter base installed with weatherproof GFCI outlets, ready to energize

2. 2

   Rough-In

   Wiring, boxes, and panel installed before walls are closed

3. 3

   Final

   All devices installed, GFCI/AFCI protection verified, panel labeled

Applies to: Change of Use / Certificate of Occupancy Permit

1. 1

   Life-Safety / Occupancy Compliance Inspection

   County inspector verifies the space meets IBC requirements for the new occupancy classification — egress, occupant load, fire separation — before sign-off.

2. 2

   Final Inspection / Certificate of Occupancy

   All work required by the permit is complete; a Certificate of Occupancy is issued before the new use may commence, consistent with this file's other final-inspection entries.

Applies to: Demolition Permit

1. 1

   Pre-Demolition

   Utility disconnects and any required asbestos clearance verified before work begins

2. 2

   Final / Site Clear

   Site cleared; call for inspection after the building is removed

Applies to: EV Charger / EVSE Permit

1. 1

   Rough-In

   Wiring, boxes, and panel/circuit installed before walls are closed, where applicable.

2. 2

   Final

   Charger installed and operational, GFCI/AFCI protection verified where required, circuit labeled.

Applies to: Fire Sprinkler & Fire Alarm Permit

1. 1

   Rough-In (Sprinkler Piping / Alarm Wiring)

   Sprinkler piping, hangers, and heads, or fire alarm conduit/wiring and devices, inspected before concealment.

2. 2

   Final Acceptance Test

   System-specific final acceptance testing (e.g., hydrostatic/flow test for sprinkler systems, functional device and notification test for alarm systems) and Fire Inspection per System sign-off before the system is placed in service.

Applies to: Mechanical / HVAC Permit

1. 1

   Rough-In

   Ductwork and gas piping installed before walls are closed

2. 2

   Final

   Equipment operational, combustion air verified, gas pressure tested

Applies to: Retaining Wall Permit

1. 1

   Footing

   Footing excavation, rebar, and forms before concrete pour — minimum 30-inch depth for frost protection

2. 2

   Final

   Wall complete, drainage functional, site graded

Applies to: Solar Panel Permit

1. 1

   Rough Electrical

   Conduit runs, wire sizing, disconnect placement before energizing

2. 2

   Final

   Panel mounting, roof penetration sealing, and electrical connections verified