Electrical / Mechanical / Plumbing (Trade) Permit — Taylor, Arizona · Requirements sheet
Verified 2026-07-07 · Source: https://www.tayloraz.gov/wp-content/uploads/2025/04/2025-Fee-Schedule.pdf
PermitBase is an independent reference and is not affiliated with any government agency. Requirements change and vary by project — confirm current details with the building department before you submit.
Electrical / Mechanical / Plumbing (Trade) Permit in Taylor, Arizona
Combined flat-fee permit category for electrical, mechanical, and plumbing installation, alteration, or repair work in the Town of Taylor, governed by the 2014 NEC, 2015 IMC, and 2015 IPC as adopted and amended by the Town. Trade permits can be applied for individually or as a combined 'M.P.E. COMBO' on the Town's Building Permit Application.
Verified 2026-07-07 · Source
When you need this permit
- Permit required to install or alter any permanent wiring or electrical device (homeowners may replace existing devices without a permit)
- Permit required for water heater replacement, altered piping within walls/ceilings/floors, and new plumbing installations (ordinary minor repairs to accessible fixtures do not require a permit)
- Permit required for heating, cooling, and ventilation system work, including wood stoves, bath vents, and gas piping (including gas line sizing per the Town's published Natural Gas Line Sizer worksheet)
- Governed by the 2014 NEC, 2015 IMC, 2015 IPC, and 2015 IFGC as adopted by the Town of Taylor
- Town's Building Permit Application supports 'ELECTRICAL', 'PLUMBING', 'MECHANICAL' as separate checkboxes, or 'M.P.E. COMBO' for combined trade work
- Generator installations require compliance with the Town's published Generator Use & Safety guidance
Required documents
Check off what you have — your progress is saved on this device.
Not ready yet — 0 of 1 required documents checked.
This checker covers one permit. A full project usually triggers several — our paid checklist will assemble all of them, from $29 →
Fee schedule
Review timeline
Inspection process
- 1
Rough-In
Wiring, piping, or ductwork verification before closure
- 2
Service/Meter (electrical only)
Service entrance and panel verification prior to utility connection
- 3
Final
Devices/fixtures/equipment installed and operational, code-compliant
See the full Taylor inspection guide — scheduling & re-inspection fees →
Tips
- The Town's current (2025) Fee Schedule lists a single flat $50 line item covering 'Electrical-Mechanical-Plumbing' rather than itemizing per-fixture/per-circuit charges — this supersedes the older 2014 Homeowner's Guide description of a per-item fee structure with a $25 minimum.
- No dedicated same-day or expedited review track for trade permits was found published by the Town; the general 'up to two weeks' plan-review figure from the Permits page is applied here as the governing published timeframe, though minor trade work is often issued over the counter in practice per the older Homeowner's Guide ('Generally plans are not required for minor plumbing, electrical or mechanical work') — this file conservatively cites the Town's own stated maximum rather than assuming same-day issuance, since no separate written same-day commitment was found.
- Solar PV Systems have their own dedicated $200 fee line, separate from the general $50 electrical-mechanical-plumbing fee.
Frequently asked questions
Sources & verification
Verified against official sources. Last reviewed 2026-07-07.
Fees, timelines, and adopted codes are researched from each jurisdiction's published records — see how we verify. Requirements change and vary by project, so always confirm the current details with the Taylor building department before you submit. PermitBase is an independent reference and is not affiliated with any government agency.
Other permits in Taylor
Electrical / Mechanical / Plumbing (Trade) Permit in other cities
Compare electrical / mechanical / plumbing (trade) permit fees across Arizona →
Look up this fee in a different city →
Now live
Build your Taylor project checklist
Describe your project once and get every permit, document, and fee it triggers in Taylor — in one checklist. Sign up and pay once to generate it, or go unlimited with Pro.
Get started →